CGI Sliding & Patio Doors Nationwide | Winslow Windows & Doors

CGI Sliding & Patio Doors: The Pompano Beach Owner’s Guide

CGI sliding and patio door parts for Pompano Beach homes typically run $220 to $640 installed, depending on whether you need rollers, a lock set, a handle, or weatherstripping, and most replacement work is done in a single visit. Homeowners usually discover a part has failed when the door starts grinding along the track, won’t seal against summer downpours, or the lock won’t throw cleanly. CGI doors are built to take a hurricane, but the moving parts work hard in this salt air and sand grit, and they don’t last forever.

Call (904) 893-3309

We stock CGI-compatible sliding door hardware on our trucks and install it across Pompano Beach weekly. If you’re fighting a door that drags, whistles, or won’t lock right, you’re in the right place.

Which CGI Models This Applies To

CGI manufactures a focused lineup of impact-rated sliding doors, and the compatibility details matter more than most people expect. The common series we see in Pompano Beach are the Estate, Sentinel, and Targa lines, plus the more recent Bordeaux sliding door systems. The Estate series uses a heavy aluminum frame with a visible interlock at the meeting rail, while the Sentinel series runs a narrower profile but thicker glass. Parts between these series are not interchangeable in most cases, especially rollers and lock hardware.

The fastest way to identify what you have is to look at the corner of the glass for the CGI etched logo and a series designation, which usually appears as a code like ES-XXX or SN-XXX on a sticker along the frame edge. If the sticker is gone, which happens after years of Florida sun, measure the door panel thickness and the roller housing width. Estate doors use a 1-1/2 inch roller housing in most vintages, while Sentinel and Targa models vary, and an aftermarket roller that’s a quarter inch off will bind or jump the track.

One compatibility gotcha we run into all the time in Pompano Beach: older CGI doors built before 2008 used a square roller housing, and the current replacements use a rounded housing. You’d think it’s close enough. It’s not. We carry both styles because swapping a square-housing roller into a round-housing frame means the door sits high on one side and the lock stops aligning. When it comes to OEM versus aftermarket, we’re honest about the tradeoff. CGI OEM parts are engineered to the exact door spec and carry the impact-rating integrity, which is the right call for rollers, interlocks, and lock sets. Quality aftermarket weatherstripping and handle hardware from reliable suppliers like Prime-Line often performs identically for less money, and we’ll tell you when that’s the case. For anything load-bearing or structural, we stick with OEM or CGI-authorized equivalents.

We’re an independent service provider, not a CGI corporate entity. That means we can match the right part without a brand rep’s sales agenda, and we’ll tell you straight when a cheaper aftermarket part does the job fine and when it won’t.

Signs Your CGI Sliding Door Is Failing

• The door grinds or shudders along the track. This is almost always a roller failure. CGI rollers use ball bearings inside a nylon or steel housing, and after enough exposure to Pompano Beach’s salt air, the bearings seize or the housing cracks. The door gets progressively harder to move, and eventually it won’t move at all.
• The lock won’t throw, or throws only with force. When rollers wear down or the door settles slightly, the lock and keep fall out of alignment. Forcing it bends the lock linkage, and then you’re replacing the lock set instead of just the rollers.
• Water pools on the floor after a hard rain. This is usually the interlock or the bottom sweep. The interlock, that vertical piece where the two panels meet, has an internal gasket that dries out and shrinks after several South Florida summers.
• You feel draft or hear traffic noise at the meeting rail. The weatherstripping at the center of the door has compressed, and once that seal is compromised, your air conditioning is escaping and outside air is getting in. In Pompano Beach humidity, you’ll see it on your electric bill.
• The handle is loose, sagging, or has more than a quarter inch of play. This is usually a broken internal spring or a stripped set screw in the handle mechanism. Left alone, the handle eventually separates from the door while you’re pulling it, which is how homeowners get hurt and frames get dented.

Replacement Cost & What’s Included

In Pompano Beach, here’s what you can expect to pay installed, parts and labor together:

• Roller replacement: $180 to $340 depending on whether it’s a single roller or a full four-roller set, plus whether your door needs the square or round housing style.
• Lock set replacement: $220 to $390 for CGI-compatible mortise or surface-mount lock sets, including alignment of the existing keep.
• Handle and latch hardware: $160 to $320, with the higher end covering interior and exterior handle pairs with keyed cylinders.
• Weatherstripping and interlock gasket replacement: $140 to $290 depending on how many runs of seal are being replaced and whether it’s the bottom sweep, the meeting rail, or the full perimeter.
• Track cleaning, alignment, and roller adjustment: $120 to $220 when the track is salvageable and the problem is adjustment, not replacement.

What drives the range is the age of the door, the series, and whether the frame itself has any warping or settling. Every quote we give is line-item: the part, the labor, the disposal. No change orders, no surprise fees on the invoice. And here’s something worth knowing, a $40 discount applies to any repair over $200, every day, no expiration. Seniors and veterans take 10% off, permanently. That’s part of how we’ve done business since 2011.

The workmanship is covered by our 36500-Day Done Right Promise. If it isn’t right, we come back and make it right. Ed’s name is on the business, and that means something specific: he personally stands behind every roller, seal, and lock his crew installs.

DIY or Call Us?

Let’s be straight about what’s safe to handle and what isn’t. A homeowner can absolutely clean the bottom track with a vacuum and a stiff brush, and that solves a surprising number of noise and binding complaints. You can also inspect the visible underside of the door for a broken roller wheel, which is a twenty-second check with a flashlight.

Here’s where DIY goes sideways on CGI doors in Pompano Beach: lifting a full-size impact door panel off its track to access the rollers. These panels weigh between 150 and 250 pounds depending on the glass package, and once the panel is off the track, you’re balancing a sheet of impact-rated glass with nothing but leverage and luck. We’ve seen homeowners drop panels, shatter the corner of the glass, pull the frame out of square, and in one memorable case in Cypress Cove, knock out a section of their own stucco trying to muscle the panel back in. The risk is not just to the door. It’s to you.

If the issue is rollers, lock alignment, or the interlock, call (904) 893-3309. We’ll come out, diagnose it honestly, and give you a line-item price before any work starts. If we can adjust it in fifteen minutes instead of selling you a part, that’s what we do.

FAQs

Get Your CGI Sliding Door Working Right Again

If your CGI sliding door is grinding, leaking, or won’t lock, don’t wait until it fails completely on a day you’re already frustrated. Call (904) 893-3309 for a free estimate. A live person answers, 24 hours a day. No voicemail loops, no call centers. We’ll schedule a time that works, show up with the truck stocked, and give you an upfront price before any work begins. We also stock parts for PGT, CWS, and ES Windows doors, so if you’ve got other doors in the house, we can handle those too.

Pompano Beach is our community. We’re the one down the road.

Written by Ed Winslow, Owner, Winslow Windows & Doors at Winslow Windows & Doors, serving Pompano Beach and nearby areas.